Copyright © 1995-2018 Michael P. Murray & Mike's Clock Clinic Mike's Clock Clinic Memberships: NAWCC 1600 Maryland Avenue Myrtle Point, OR 97458-1508 Phone: 541-559-1090, or 877-286-6762 (Toll Free) E-mail address: Mike@telechron.us (Preferred contact method)Respectfully, Michael P. Murray Memberships Include: National Association of Watch & Clock Collectors An Internet private E-mailing list called Clocksmiths N.A.W.C.C. National 400-day Clock Chapter # 168 A service from, E-mail address: Mike@telechron.us Mike Murray Founder of Clocksmiths A specialist in Atmos and 400-day clock repair. Also, I overhaul most plug in electric clocks. In continuous service since 04/01/1982. Mike's Clock Clinic Memberships: Clocksmiths & NAWCC 1600 Maryland Avenue Myrtle Point, OR 97458-1508 Phone: 541-559-1090, or 877-286-6762 (Toll free) My main Web site is located at http://www.atmosman.com/ Main FTP site is located at http://home.earthlink.net/~atmosman/earthpdf.html Memberships: Clocksmiths & NAWCC N.A.W.C.C. International 400-day Clock Chapter # 168 Published in Chapter 168's "Torsion Times" Published in AWCI's "Horological Times" Formally AWCI's 400-day (Anniversary) clock Bench Course Instructor!
Telechron "H" Clock Rotors Turning @ 14.4 R.P.M.'s (M-3218) & (M-3473)
My business is rebuilding your original rotor. The type "H" is the standard sized rotor. All 14.4 R.P.M. "H" rotors cost $150.00 plus $15.00 priority mail (Canada is $40.00) and have a 2-year warranty, which brings your total cost to $165.00 assuming you send the old rotor at time of payment. The reason for the price increase is because "H's" turning at 14.4 R.P.M.'s are extremely rare. I must have the old rotor or add $100.00. Aluminum rotors will NOT qualify as an exchange for their copper and nickel counterparts. Typically aluminum rotors have a M # of 3300 or higher. My turnaround is 6 to 8 weeks for motor/rotor service, 4 to 6 months if the clock is sent with the motor/rotor, and 8 to 10 months for a movement overhaul. Expedited service take about 2 weeks for motor/rotor service, one month if the clock is sent with motor/rotor. Expedited service adds $100.00 unless it is a movement overhaul then the movement overhaul labor is doubled. If you want to send in the clock for motor or rotor replacement, please be advised that shipping will jump from $15.00 to $100.00 with everything else staying the same. The increase covers return shipping and insurance and includes my labor charge of $50.00 for the replacement ($250.00 total). One thing you can do before you send in the motor (coil, field, & rotor) is to take a Multimeter or Volt/Ohm meter, these are less than $20.00 at any hardware store, and with no current on the clock, set the meter to Ohms and touch the two leads to the end of the wires or the posts on the coil where the wires connect and see if you get a reading. Just about any reading is a good one. But if you get no reading what-so-ever then the motor's coil is dead and you'll need a replacement coil. I'll not ship the rotor/motor until I received payment. I ONLY accept money orders, certified checks, or company checks for payment but repeat customers may use personal checks. Normally shipping takes place one week or so after I receive payment and thanks !
For return shipping I use USPS for all shipping. If you want to use another carrier then you will have to arrange everything for shipping, meaning I hand the box to the driver, get a receipt and nothing else.
I would like payment by money order, certified check, personal check, business check, or through Pay Pal or Square, which is the only way I take credit cards. I do prefer a check over Pay Pal or Square because Pay Pal and Square take 3%. I only take credit cards if you are in the USA or Canada. The 3% is added to the total bill if you use a credit card. With Pay Pal you can pay me directly using "friends and family" where you absorb all fees and I'm paid the full amount. There would be nothing added amount to the final fill if you absorb all fees. Here you log on to Pay Pal and send me the full amount of my bill, so there is no E-voice coming from me with this method and you will be charged all Pay Pal fees on top of my final bill. With either Pay Pal or Square, I will send an invoice to your E-mail address. Here you are dealing directly with either service and not me. You do have to be a member of Pay Pal in order to issue a payment but you may use Square without any membership or additional Square fees but the 3% will be added to your total bill as with Pay Pal. With Square, I can also take the credit card information which includes the number, expiration date and the last 3 or 4 #'s of the security code from the back of the card BUT that adds 3.5% to the final bill. I'd prefer to avoid this method but it is an option. All of the added fees are exactly what either service charges me for taking your credit card.
My main Web site is located at http://www.atmosman.com/ Main FTP site is located at http://home.earthlink.net/~atmosman/earthpdf.html